What Network Cabling to Ask for When Renovating a Dental Office

By Starcomm Technologies ·

When you renovate a dental office, ask for Cat6 or Cat6A network cable run to every spot where a computer, imaging device, phone, Wi-Fi access point or security camera will sit. Each operatory should get spare drops (a drop is one cable ending in a wall or ceiling jack), and every cable should run back to one tidy, ventilated network closet. Ask for every cable to be labelled and tested, with a written report, and get it all done while the walls are still open.

Below we walk through what that means in practice, so you can hand a clear list to your contractor or cabling installer.

Why does cabling matter so much in a dental renovation?

Almost everything in a modern clinic depends on the network: your practice management software (Dentrix, ABELDent, Tracker, ClearDent and others), digital X-rays and scans, phones, card terminals and cameras. Wi-Fi helps, but the devices that matter most work better on a wired connection, which is steadier and less affected by walls and interference.

The catch is timing. Running cable while studs are exposed is fairly simple. Running it after drywall, paint and cabinetry go in means opening walls, fishing cable through tight spaces and working around a clinic that is trying to see patients. A renovation is the best chance you will get to do it properly.

Which type of cable should you ask for?

Ask for Cat6 or Cat6A cable. These are categories of network cable; the higher the category, the more data it can carry reliably.

  • Cat6 handles typical clinic needs well today, including large imaging files moving between operatories and the server.
  • Cat6A costs more but gives more room for faster equipment later and is less prone to interference. It is worth considering for long runs, imaging rooms and Wi-Fi access points.

A few other points to put in writing:

  • Solid copper cable. Some cheap cable is copper-clad aluminium, which performs poorly and can cause problems with devices powered through the cable. Ask for solid copper.
  • The right fire rating. Cable running through ceiling spaces used for air return often needs a plenum rating. Your contractor and local building inspector will know what the code requires for your space.
  • Distance limits. A standard network cable run is limited to roughly 100 metres. In a larger clinic, the closet location matters.

How many network drops does each room need?

Plan for every device you have now, then add spares. Equipment changes over the life of a renovation far more than the walls do.

Operatories

Each operatory usually has a computer, often a phone, sometimes a patient-facing monitor, and possibly an intraoral camera or sensor setup. Ask for drops at the computer location and near the delivery unit or wherever the screen will be mounted, plus at least one spare. Mark the exact heights and positions on the drawings so cabinetry does not cover them.

Front desk and checkout

The front desk is busy: computers, phones, printers, a label printer, card terminals and sometimes a check-in screen. Ask for more drops than you think you need here. VoIP phones (phones that run over the internet) often draw power through the network cable, called PoE or power over Ethernet, so a dedicated drop per phone keeps things simple. Our VoIP phone page explains more.

Imaging rooms

Panoramic and CBCT (3D) units usually need a dedicated network connection to their acquisition computer, and manufacturers such as Dexis, Carestream, Planmeca and Vatech publish installation requirements. Get those specifications from your imaging dealer before the cabling plan is final. We cover more of this in setting up dental imaging and intraoral cameras.

Other rooms

  • Doctor's office and consult room: a computer drop and a phone drop, plus a spare.
  • Sterilization area: a drop if you track instruments or log cycles electronically.
  • Staff room and lab: at least one drop each.
  • Printer and copier locations: one drop each.

Ceiling drops

Ask for ceiling drops for Wi-Fi access points, placed so coverage reaches every operatory, and for security cameras if you plan to add them. Both are usually powered through the cable, so no outlet is needed at the ceiling.

Where should all the cables go back to?

Every cable should end in one central spot, usually a small network closet or wall-mounted rack. Ask for:

  • Ventilation or cooling. Switches, firewalls and servers give off heat. A sealed storage closet can get hot enough to shorten equipment life.
  • A dedicated power circuit with enough outlets for the rack and a battery backup unit.
  • Room to work. A technician needs to stand in front of the rack and open it.
  • A lock. This equipment handles patient information, so it should not sit in an open hallway or a room the public can reach.
  • A path for the internet line. Your internet provider's cable needs to reach this room too.

What should the finished job include?

A good cabling job is more than cable in walls. Ask your installer to provide:

  1. A patch panel in the rack, so each cable ends in a neat numbered port rather than loose wires.
  2. Matching labels on every wall jack and patch panel port.
  3. Testing of every cable with proper test equipment, and a written report showing each result.
  4. A floor plan marking where every numbered drop is.
  5. Spare capacity, such as empty conduit or pull strings to key areas, so adding a cable later does not mean opening a wall.
  6. Clean cable management in the ceiling and rack, kept clear of electrical wiring and lighting ballasts.

Keep the test report and floor plan with your clinic records. They save a lot of time when something needs troubleshooting later.

A checklist to bring to your contractor

Use these questions before the walls close:

  1. Will you use Cat6 or Cat6A, solid copper, with the fire rating our space requires?
  2. How many drops are planned for each operatory, the front desk and the imaging room, and where are the spares?
  3. Have you confirmed the imaging manufacturer's network requirements?
  4. Where will the network closet be, and does it have ventilation, a dedicated circuit and a lock?
  5. Are there ceiling drops for Wi-Fi access points and cameras?
  6. Will every cable be labelled, tested and documented with a report and floor plan?
  7. Who is coordinating with the electrician, dental equipment dealer, phone provider and internet provider?

When should the cabling installer get involved?

As early as possible, ideally at the drawing stage. The cabling plan depends on where chairs, cabinets, monitors and imaging units will go, so it works best when your designer, dental equipment dealer, electrician and IT company review the plan together. Leaving cabling to the last week of construction is where clinics end up with jacks behind cabinets or not enough drops at the front desk.

If you lease space in a plaza or medical building, check with your landlord about where cable may run and whether there is a shared telecom room.

How Starcomm can help

We have supported dental clinics across Mississauga, Toronto and the GTA since 1999, and we plan and install network cabling and Wi-Fi with dental equipment and practice software in mind. We can review your renovation drawings, work with your contractor and equipment dealer, and set up the network closet so it is ready for your computers, imaging and phones.

If you have a renovation coming up, call us at 905-816-9797 or contact us and we will talk through your plans.

Frequently asked questions

Is Cat6A worth the extra cost for a dental office?

It depends on the size of the clinic and how long you plan to stay. Cat6 handles typical clinic needs well, while Cat6A gives more room for faster equipment later and is a sensible choice for long runs, imaging rooms and Wi-Fi access points.

Can we rely on Wi-Fi instead of running network cable?

Wi-Fi is useful for tablets and laptops, but computers, imaging equipment and phones are steadier on a wired connection. Wi-Fi access points also need network cable to reach them, so cabling is still part of the plan.

Can our electrician run the network cable?

Some electricians do low-voltage work, but ask whether they will test and document every cable and terminate it on a labelled patch panel. Whoever does it should coordinate with your IT company so the drops match your equipment.

Should we reuse the old network cable during a renovation?

Older cable may be a lower category, damaged, or poorly labelled, and the walls being open is the easiest time to replace it. Have it tested before deciding to keep any of it.

Do we need permission to run cable in a leased unit?

Often, yes. Check your lease and ask your landlord or property manager where cable may run and whether the building has a shared telecom room for your internet line.

← All posts